Network Working Group Thomas D. Nadeau Internet Draft Cisco Systems, Inc. Category: Standards Track Expiration Date: September 2007 George Swallow Cisco Systems, Inc. March 2007 Detecting MPLS Data Plane Failures in Inter-AS and inter-provider Scenarios draft-ietf-mpls-interas-lspping-00.txt Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html Abstract This document describes a simple and efficient mechanism that can be used to detect data plane failures in Multi-Protocol Label Switching Label Switched Paths that extend beyond a single Autonomous System and/or across multiple Service Provider network boundaries. This document describes extensions to the existing MPLS LSP Ping protocol to achieve these goals. Nadeau & Swallow Standards Track [Page 1] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 Contents 1 Introduction .............................................. 3 2 Terminology ............................................... 3 2.1 Conventions used in this document ......................... 3 2.2 Terminology ............................................... 3 2.3 Acronyms .................................................. 4 3 Structure of This Document ................................ 4 4 Motivation ................................................ 4 5 Inter-AS TLVs ............................................. 5 5.1 Inter-AS TLV .............................................. 5 5.1.1 IPv4 Inter-AS TLV ......................................... 7 5.1.2 IPv6 Inter-AS TLV ......................................... 8 5.1.3 Visited ASBR Address Stack ................................ 9 6 Error Code(s) ............................................. 11 7 Theory of Operation ....................................... 11 7.1 Adjustments to Outgoing Labels ............................ 12 7.2 Receiving Echo Replies .................................... 12 8 Security Considerations ................................... 14 9 IANA Considerations ....................................... 14 9.1 Message Types, Reply Modes, Return Codes .................. 14 9.2 TLVs ...................................................... 15 10 References ................................................ 15 10.1 Normative References ...................................... 15 10.2 Informative References .................................... 15 11 Acknowledgments ........................................... 16 12 Authors' Addresses ........................................ 16 Nadeau & Swallow Standards Track [Page 2] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 1. Introduction This document describes a simple and efficient mechanism that can be used to detect data plane failures in MPLS LSPs that span across mul- tiple Autonomous System (AS) and service provider boundaries. At present, the existing MPLS LSP Ping protocol cannot handle all but one of these cases. This document first explains the scenarios where the existing protocol is inadequate, then describes information car- ried in extended MPLS "echo request" and "echo reply" messages; and finally describes enhanced mechanisms for transporting the echo reply, as well as processing it at intermediate points (both in an out of the originating AS). An important consideration in this design is that MPLS echo requests follow the same data path that normal MPLS packets would traverse. MPLS echo requests are meant primarily to validate the data plane, and secondarily to verify the data plane against the control plane. Mechanisms to check the control plane are valuable, but are not cov- ered in this document. As is described in [RFC4379], to avoid potential Denial of Service attacks, it is recommended to regulate the LSP ping traffic going to the control plane. A rate limiter should be applied to the well- known UDP port defined below. Furthermore, due to the fact that there are data exchanges between provider networks which may wish to hide the details of their network, it is recommended that the inter- AS border routers provide operators with control over what informa- tion (i.e.: addresses) in these messages. 2. Terminology 2.1. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 2.2. Terminology Definitions of key terms for MPLS OAM are found in [RFC4378] and the reader is assumed to be familiar with those definitions which are not repeated here. The following additional terms are useful to understand this docu- ment. Nadeau & Swallow Standards Track [Page 3] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 2.3. Acronyms The following list of acronyms is a repeat of common acronyms defined in many other documents, and is provided here for convenience. CE: Customer Edge PE: Provider Edge ASBR: Autonomous System Border Router DoS: Denial of service ECMP: Equal Cost Multipath LDP: Label Distribution Protocol LSP: Label Switch Path LSR: Label Switch Router OAM: Operations and Management OA&M: Operations, Administration and Maintenance. RSVP: Resource reSerVation Protocol SP: Service Provider 3. Structure of This Document The body of this memo contains four main parts: motivation, exten- sions to the MPLS echo request/reply packet format, inter-AS LSP ping operation, and a reliable return path. It is suggested that first- time readers skip the actual packet formats and read the Theory of Operation first; the document is structured the way it is to avoid forward references. 4. Motivation The requirements specified in [RFC4377] stipulate that data plane OAM functions must be provided as solutions for service providers. These data plane test functions must not only function within an autonomous system (AS), but must also function across ASs. Furthermore, these tests must function correctly across ASs that span multiple Service Provider(SP) domains. At present, the data plane liveliness tools function in these capacities only in the narrow (and rarely used) case where the IP addresses of LSRs involved are known to each other. For example, when the IP addresses from one AS are exchanged through routing with other attached ASs. Another case includes the Layer-3 VPN inter-provider interconnection where the PE addresses are dis- tributed between service providers. However, these cases are uncom- mon, and thus the existing LSP Ping [RFC4379] tool is unable to respond under most error condition configurations. For example con- sider the following configuration. Imagine that PE1 and PE2 are in two different provider domains. In this case, it is common for providers to NOT distribute the IP addresses of any of the routers other than the ASBR. Nadeau & Swallow Standards Track [Page 4] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 {---- AS1 ----} {---- AS2 ----} PE1--P---P--ASBR1----ASBR2--P---P--PE2 Now, imagine that the LSP that connects PE1 to PE2 contains a fault somewhere bewteen ASBR2 and PE2 as is indicated by 'X' between the two P routers: {---- AS1 ----} {---- AS2 ----} PE1--P---P--ASBR1----ASBR2--P-X-P--PE2 If an LSP Ping is initiated at PE1 with a destination of PE2 and a source of PE1, the packet is label switched correctly until it reaches the first P router within AS2. Here lets imagine that MPLS forwarding is disabled on the link between the two P routers. Upon discovering this while attempting to process the LSP Ping Request packet, the first P router will attempt to reply directly to PE1 with the appropriate error code 5. However, because the address of PE1 is actually private to AS1 by virtue of not being distributed by ASBR1 into AS2, the P router cannot correctly forward the reply to PE1. In this case, PE1 may surmise that some failure has occurred, but it cannot determine what the error is or where it exists. This clearly does not meet the requirements stipulted in [RFC4377]. This draft describes extensions to [RFC4379] that overcome the aforementioned limitations, and thus allow for the handling of inter-AS/provider cases. 5. Inter-AS TLVs 5.1. Inter-AS TLV The Inter-AS TLV Reply Object is an optional TLV that is used to col- lect and report the ASBRs along the path of the LSP under test. Only one such object may appear in a Reply message. The purpose of this object is to allow the downstream router to relay a Reply message from ASBR to ASBR when a failure is detected. A router will use this TLV to look up the last ASBR as indicated as the top-most address on the address stack, that forwarded the Request message into its AS, and then forward the Reply to that router after popping the address from the stack. The Reply message will ultimately be relayed to the original soure of the request. This message has one format that con- tains the true source and destination addresses of the Request mes- sage, as well as a stack of ASBR addresses that were visited while forwarding this message. Type 17 is defined for this TLV (to be assigned by IANA). Nadeau & Swallow Standards Track [Page 5] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 17 (Inter-AS TLV) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Node IP Address (4 or 16 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Node AS Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node IP Address (4 or 16 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node AS Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node Contact String | | | | (16 octets) | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SubType | SubLength | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Visited ASBR Address Stack | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ SubType: Sub-Type # Length Value Field ---------- ------ ------------- 1 6 IPv4 Return Stack 2 6 IPv4 Trace Stack 3 6 Ipv6 Return Stack 4 6 IPv6 Trace Stack Note that only combinations of 1+2 or 3+4 may be used. Support of mixed IPv4 and IPv6 ASes is beyond the scope of this document. Failed Node AS Number: This field may contain the AS number in which the node where the failure was detected resides. If no AS number is indicated, this field MUST contain 0s. Failed Node IP Address: This must be a valid IPv4 or IPv6 address assigned to the router. If the interface to the downstream LSR is numbered, then the Address Type MUST be set to IPv4 or IPv6, Failed Node IP Address MUST be set to either the downstream LSR's Router ID or the Nadeau & Swallow Standards Track [Page 6] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 interface address of the downstream LSR. If the interface to the downstream LSR is unnumbered, the Address Type MUST be Unnumbered, the Downstream IP Address MUST be the downstream LSR's Router ID. Failed Node AS Number: This field may contain the AS number in which the node where the failure was detected resides. If no AS number is indicated, this field MUST contain 0s. Failed Node Contact String: This field may contains a string of ASCII characters inserted by the node where the failure was detected or by its closest ASBR. This field MUST indicate contact information such as a provider's international phone number and other relevant contact information in cases where local policy dictates that a provider will not fill in the Failed Node AS number and/or the Failed Node Address. In all other cases, this field MUST contain 0s. 5.1.1. IPv4 Inter-AS TLV The value consists of four octets of an IPv4 prefix followed by one octet of prefix length in bits; the format is given below. The IPv4 prefix is in network byte order; if the prefix is shorter than 32 bits, trailing bits SHOULD be set to zero. . Nadeau & Swallow Standards Track [Page 7] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 17 (Inter-AS TLV) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Node IPv4 Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Node AS Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node IPv4 Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node AS Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node Contact String | | | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SubType | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 5.1.2. IPv6 Inter-AS TLV The value consists of 16 octets of an IPv6 prefix followed by one octet of prefix length in bits; the format is given below. The IPv6 prefix is in network byte order; if the prefix is shorter than 128 bits, trailing bits SHOULD be set to zero. This FEC is used if the protocol advertising the label is unknown, or may change during the course of the LSP. An example is ani nter-AS LSP that may be sig- naled by LDP in one AS, by RSVP-TE in another AS, and by BGP between the ASs, such as is common for inter-AS VPNs. Nadeau & Swallow Standards Track [Page 8] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 17 (Inter-AS TLV) | Length = 5 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Node IPv6 Address | | (16 octets) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Node AS Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node IPv6 Address | | (16 octets) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node AS Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Failed Node Contact String | | | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SubType | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 5.1.3. Visited ASBR Address Stack The term Visited ASBR Address Stack applies to two stacks of IP addresses of the ASBRs along the path of an LSP called the Trace and Return Stacks. The two stacks have the same format; however they have slightly different semantics. Both stack objects are stacks of addresses that denote the list of visited ASBRs. The obeject is a stack either an IPv4 address if the TLV SubType field is set to 1 or 2, or an IPv6 address if the TLV SubType field is set to 3 or 4. The Return Stack is to be used in a destructive manner as a means of unwinding the path of ASBRs that were used to originally forward the Request. Each subsequent ASBR along the path that receives the reply should destructively remove itself from the stack. On the other hand, the Trace Stack MUST only be added to (i.e.: ASBR addresses pushed) and items never removed from this stack. This will allow the source to see the trace of the path of ASBRs once the Reply message is returned. In cases where policy dictates that ASBR Nadeau & Swallow Standards Track [Page 9] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 addresses must be hidden, a value of all 0s MUST be inserted into the stack, or the stack completely removed prior to forwarding the Reply. It is prefered that a blank entry be left, as this will at least indicate that there was one hop without revealing its IP address. IPv4 Trace and Visited Stack Objects The Length is 4*N octets, N is the number of visited ASBRs. This object has the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ASBR IPv4 Address 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ASBR IPv4 Address 2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . ... . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ASBR IPv4 Address N | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ASBR IPv4 Address 1, ASBR IPv4 Address 1, ... contain a valid IPv4 address. IPv6 Trace and Visited Stack Objects The Length is 16*N octets, N is the number of visited ASBRs. This object has the following format: Nadeau & Swallow Standards Track [Page 10] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ASBR IPv6 Address 1 | | ASBR IPv6 Address (Cont.) | | ASBR IPv6 Address (Cont.) | | ASBR IPv6 Address (Cont.) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . ... . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ASBR IPv6 Address N | | ASBR IPv6 Address (Cont.) | | ASBR IPv6 Address (Cont.) | | ASBR IPv6 Address (Cont.) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ASBR IPv6 Address 1, ASBR IPv6 Address 1, ... contain a valid IPv4 address. IPv6 6. Error Code(s) TBD 7. Theory of Operation hen tracing an LSP which spans multiple AS, an Inter-AS Reply Object s included in the Echo Request. Initially the object contains only he address of the source PE and a Trace stack with that same address. s the tracing progress each ASBR copies the trace stack as a reply tack, it then pushes its address to the trace stack. It includes oth stacks in an Inter-AS Reply object and sends it in an Echo eply mes- sage to the top address in the reply stack. The receiver f the Reply message then verifies that it is included in the reply tack. It then pops its address from the reply stack and e-addresses the Echo Reply message to the (new) top element of the eply stack. This is repeated until the source PE receives the cho Reply. Nadeau & Swallow Standards Track [Page 11] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 7.1. Adjustments to Outgoing Labels When an LSP request is sent from an originator, some adjustments may need to be made to outgoing labels: Inter-AS cases: A) VRF to VRF The LSP terminates at the ASBR. These procedures do not apply. B) EBGP redistribution of labeled VPN-IPv4 routes from AS to neighboring AS. Tracing is performed by incrementing the VPN label begining at one. If TTL hiding is in effect, then tracing of PSN label is not necessary for these procedures. C) Carrier's Carrier (CsC): 1) TTL Hiding a. Will work as is. b. Verification of the core must be done separately by core own- ers. c. Traceroute can trace both stubs of the 'carried' carrier. 2) No TTL hiding a. Set VPN TTL to 1. b. CsC CE or Ps would return to the CsC PE who would relay mes- sages back to originator. c. For traceroute, set VPN TTL=1, and progressively increase the IGP TTL by 1 to probe. 7.2. Receiving Echo Replies The existing packet processing algorithm as specified in [RFC4379] is enhanced as follows to support inter-AS/provider LSP ping/trace. When an Echo Reply message is received: 1) If the packet is addressed to this router (i.e.: destination address == this router's router ID): a. If the original sender field TLV == this router's address, process normally. // today's functionality for a normal Nadeau & Swallow Standards Track [Page 12] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 reply received by the src. b. Else this packet has been delivered to this router because it is an ASBR and needs to proxy for a P router in its AS to return the reply. If the inter-AS TLV is present, i. If the last visited AS is empty, set it to the ASBR's primary AS#. ii. If the stack is empty, this is an error case. The TLV SHOULD NOT be present if the stack is empty. iii. Else if the top-most address in the stack is this router's address. 1. Pop it from the stack. 2. Replace the packet's destination address with the next address in the stack. 3. Replace the packet's src address with this ASBR's address. 4. Optionally, the ASBR may hide (i.e.: remove) information that its local policy has been configured for. 5. Look up the route/next-hop for this address and deliver the packet. The ASBR should be able to resolve the address because at this point unless there has been an error in the return path forwarding, then the packet should be at the border of the originating AS. If the look-up fails, drop the packet and notify the operator of this router that an error condition has occurred. When an LSP ping request is received: 2) If this router is an ASBR a. Write the next entry in the Last Seen ASBR stack's address as the destination address of the packet and forward it to that address. b. Otherwise process normally as specified in the LSP ping draft. Nadeau & Swallow Standards Track [Page 13] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 8. Security Considerations In addition to the Security Considerations from [RFC4379], here are at least two approaches to attacking LSRs using the mecha- nisms defined here. One is a Denial of Service attack, by sending MPLS echo requests/replies to LSRs and thereby increasing their workload. The other is obfuscating the state of the MPLS data plane liveness by spoofing, hijacking, replaying or otherwise tampering with MPLS echo requests and replies. Authentication will help reduce the number of seemingly valid MPLS echo requests, and thus cut down the Denial of Service attacks; beyond that, each LSR must protect itself. Authentication sufficiently addresses spoofing, replay and most tam- pering attacks; one hopes to use some mechanism devised or suggested by the RPSec WG. It is not clear how to prevent hijacking (non- delivery) of echo requests or replies; however, if these messages are indeed hijacked, LSP ping will report that the data plane isn't work- ing as it should. It doesn't seem vital (at this point) to secure the data carried in MPLS echo requests and replies, although knowledge of the state of the MPLS data plane may be considered confidential by some. 9. IANA Considerations [need to request some new Message Types, TLV Types, Return Codes] 9.1. Message Types, Reply Modes, Return Codes It is requested that IANA maintain registries for Message Types, Reply Modes, Return Codes and Return Subcodes. Each of these can take values in the range 0-255. Assignments in the range 0-191 are via Standards Action; assignments in the range 192-251 are made via Expert Review; values in the range 252-255 are for Vendor Private Use, and MUST NOT be allocated. If any of these fields fall in the Vendor Private range, a top-level Vendor Enterprise Code TLV MUST be present in the message. Nadeau & Swallow Standards Track [Page 14] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 9.2. TLVs It is requested that IANA maintain registries for the Type field of top-level TLVs as well as for sub-TLVs. The valid range for each of these is 0-65535. Assignments in the range 0-16383 and 32768-49161 are made via Standards Action as defined in [RFC2434]; assignments in the range 16384-31743 and 49162-64511 are made via Expert Review (see below); values in the range 31744-32746 and 64512-65535 are for Ven- dor Private Use, and MUST NOT be allocated. If a TLV or sub-TLV has a Type that falls in the range for Vendor Private Use, the Length MUST be at least 4, and the first four octets MUST be that vendor's SMI Enterprise Code, in network octet order. The rest of the Value field is private to the vendor. 10. References 10.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC4377] Nadeau, T., Morrow, M., Swallow, G., Allan, D., Matshushima, S., "Operations and Management (OAM) Requirements for Multi-Protocol Label Switched (MPLS) Networks", RFC 4377, February 2006. [RFC4378] Allan, D., Nadeau, T., "A Framework for Multi-Protocol Label Switching (MPLS) Operations and Management", RFC 4378, February 2006. [RFC4379] Kompella, k., Swallow, G., "Detecting MPLS Data Plane Liveness", RFC 4379, February 2006. 10.2. Informative References [RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 2434, October 1998. Nadeau & Swallow Standards Track [Page 15] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 11. Acknowledgments The authors wish to acknowledge and thank the following individuals for their valuable comments to this document: Azhar Sayeed, Vanson Lim, and Mike Piecuch. 12. Authors' Addresses Thomas D. Nadeau Cisco Systems, Inc. 1414 Massachusetts Ave, Boxboro, MA 01719 Phone: +1.978.936.1470 Email: tnadeau@cisco.com George Swallow Cisco Systems 1414 Massachusetts Ave, Boxborough, MA 01719 Phone: +1 978 936 1398 Email: swallow@cisco.com Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assur- ances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org. Nadeau & Swallow Standards Track [Page 16] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 Full Copyright Notice Copyright (C) The IETF Trust (2007). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Nadeau & Swallow Standards Track [Page 17] Internet Draft draft-ietf-mpls-interas-lspping-00.txt March 2007 Nadeau & Swallow Standards Track [Page 18]