Network Working Group R. Aggarwal (Editor) Internet Draft Juniper Networks Expiration Date: July 2007 D. Papadimitriou (Editor) Alcatel S. Yasukawa (Editor) NTT January 2007 Extensions to RSVP-TE for Point-to-Multipoint TE LSPs draft-ietf-mpls-rsvp-te-p2mp-07.txt Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract This document describes extensions to Resource Reservation Protocol - Traffic Engineering (RSVP-TE) for the set up of Traffic Engineered (TE) point-to-multipoint (P2MP) Label Switched Paths (LSPs) in Multi- Protocol Label Switching (MPLS) and Generalized MPLS (GMPLS) networks. The solution relies on RSVP-TE without requiring a multicast routing protocol in the Service Provider core. Protocol Raggarwa, Papadimitriou & Yasukawa [Page 1] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 elements and procedures for this solution are described. There can be various applications for P2MP TE LSPs such as IP multicast. Specification of how such applications will use a P2MP TE LSP is outside the scope of this document. Raggarwa, Papadimitriou & Yasukawa [Page 2] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 Table of Contents 1 Conventions used in this document ..................... 5 2 Terminology ........................................... 5 3 Introduction .......................................... 5 4 Mechanism ............................................. 6 4.1 P2MP Tunnels .......................................... 6 4.2 P2MP LSP ............................................. 6 4.3 Sub-Groups ............................................ 7 4.4 S2L Sub-LSPs .......................................... 7 4.4.1 Representation of an S2L Sub-LSP ...................... 7 4.4.2 S2L Sub-LSPs and Path Messages ........................ 8 4.5 Explicit Routing ...................................... 8 5 Path Message .......................................... 11 5.1 Path Message Format ................................... 11 5.2 Path Message Processing ............................... 12 5.2.1 Multiple Path Messages ................................ 12 5.2.2 Multiple S2L Sub-LSPs in one Path message ............. 13 5.2.3 Transit Fragmentation of Path State Information ....... 15 5.2.4 Control of Branch Fate Sharing ........................ 16 5.3 Grafting .............................................. 16 6 Resv Message .......................................... 17 6.1 Resv Message Format ................................... 17 6.2 Resv Message Processing ............................... 18 6.2.1 Resv Message Throttling ............................... 19 6.3 Route Recording ....................................... 20 6.3.1 RRO Processing ........................................ 20 6.4 Reservation Style ..................................... 20 7 PathTear Message ...................................... 21 7.1 PathTear Message Format ............................... 21 7.2 Pruning ............................................... 21 7.2.1 Implicit S2L Sub-LSP Teardown ......................... 21 7.2.2 Explicit S2L Sub-LSP Teardown ........................ 22 8 Notify and ResvConf Messages .......................... 22 8.1 Notify Messages ....................................... 22 8.2 ResvConf Messages ..................................... 24 9 Refresh Reduction ..................................... 25 10 State Management ...................................... 25 10.1 Incremental State Update .............................. 25 10.2 Combining Multiple Path Messages ...................... 26 11 Error Processing ...................................... 27 11.1 PathErr Messages ...................................... 27 11.2 ResvErr Messages ...................................... 28 11.3 Branch Failure Handling ............................... 29 12 Admin Status Change ................................... 30 Raggarwa, Papadimitriou & Yasukawa [Page 3] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 13 Label Allocation on LANs with Multiple Downstream Nodes ..30 14 P2MP LSP and Sub-LSP Re-optimization .................. 30 14.1 Make-before-break ..................................... 30 14.2 Sub-Group Based Re-optimization ....................... 31 15 Fast Reroute .......................................... 31 15.1 Facility Backup ....................................... 32 15.1.1 Link Protection ....................................... 32 15.1.2 Node Protection ....................................... 32 15.2 one-to-one Backup ..................................... 33 16 Support for LSRs that are not P2MP Capable ............ 34 17 Reduction in Control Plane Processing with LSP Hierarchy. 36 18 P2MP LSP Remerging and Cross-Over ..................... 36 18.1 Procedures ............................................ 37 18.1.1 Re-Merge Procedures ................................... 38 19 New and Updated Message Objects ....................... 40 19.1 SESSION Object ........................................ 40 19.1.1 P2MP LSP Tunnel IPv4 SESSION Object ................... 40 19.1.2 P2MP LSP Tunnel IPv6 SESSION Object ................... 41 19.2 SENDER_TEMPLATE object ................................ 41 19.2.1 P2MP LSP Tunnel IPv4 SENDER_TEMPLATE Object ........... 42 19.2.2 P2MP LSP Tunnel IPv6 SENDER_TEMPLATE Object ........... 42 19.3 S2L_SUB_LSP Object .................................... 43 19.3.1 S2L_SUB_LSP IPv4 Object ............................... 44 19.3.2 S2L_SUB_LSP IPv6 Object ............................... 44 19.4 FILTER_SPEC Object .................................... 44 19.4.1 P2MP LSP_IPv4 FILTER_SPEC Object ...................... 44 19.4.2 P2MP LSP_IPv6 FILTER_SPEC Object ...................... 45 19.5 P2MP SECONDARY_EXPLICIT_ROUTE Object (SERO) ........... 45 19.6 P2MP SECONDARY_RECORD_ROUTE Object (SRRO) ............. 45 20 IANA Considerations ................................... 45 20.1 New Class Numbers ..................................... 45 20.2 New Class Types ....................................... 46 20.3 New Error Values ...................................... 46 20.4 LSP Attributes Flags .................................. 47 21 Security Considerations ............................... 47 22 Acknowledgements ...................................... 48 23 References ............................................ 48 23.1 Normative References .................................. 48 23.2 Informative References ................................ 49 24 Appendix .............................................. 50 24.1 Example ............................................... 50 25 Author Information .................................... 51 25.1 Editor Information .................................... 51 25.2 Contributor Information ............................... 52 26 Intellectual Property ................................. 54 27 Full Copyright Statement .............................. 54 28 Acknowledgement ....................................... 55 Raggarwa, Papadimitriou & Yasukawa [Page 4] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 1. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC-2119 [RFC2119]. 2. Terminology This document uses terminologies defined in [RFC3031], [RFC2205], [RFC3209], [RFC3473], [RFC4461] and [RFC4090]. 3. Introduction [RFC3209] defines a mechanism for setting up point-to-point (P2P) Traffic Engineered (TE) Label Switched Paths (LSPs) in Multi-Protocol Label Switching (MPLS) networks. [RFC3473] defines extensions to [RFC3209] for setting up P2P TE LSPs in Generalized MPLS (GMPLS) networks. However these specifications do not provide a mechanism for building point-to-multipoint (P2MP) TE LSPs. This document defines extensions to the RSVP-TE protocol [RFC3209], [RFC3473] to support P2MP TE LSPs satisfying the set of requirements described in [RFC4461]. This document relies on the semantics of the Resource Reservation Protocol (RSVP) that RSVP-TE inherits for building P2MP LSPs. A P2MP LSP is comprised of multiple source-to-leaf (S2L) sub-LSPs. These S2L sub-LSPs are set up between the ingress and egress-LSRs and are appropriately combined by the branch LSRs using RSVP semantics to result in a P2MP TE LSP. One Path message may signal one or multiple S2L sub-LSPs for a single P2MP LSP. Hence the S2L sub-LSPs belonging to a P2MP LSP can be signaled using one Path message or split across multiple Path messages. There are various applications for P2MP TE LSPs and the signaling techniques described in this document can be used, sometimes in combination with other techniques, to support different applications. Specification of how applications will use P2MP TE LSPs and how the paths of P2MP TE LSPs are computed is outside the scope of this document. Raggarwa, Papadimitriou & Yasukawa [Page 5] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 4. Mechanism This document describes a solution that optimizes data replication by allowing non-ingress nodes in the network to be replication/branch nodes. A branch node is an LSR that replicates the incoming data on to one or more outgoing interfaces. The solution relies on RSVP-TE in the network for setting up a P2MP TE LSP. The P2MP TE LSP is set up by associating multiple S2L sub-LSPs and relying on data replication at branch nodes. This is described further in the following sub-sections by describing P2MP Tunnels and how they relate to S2L sub-LSPs. 4.1. P2MP Tunnels The defining feature of a P2MP TE LSP is the action required at branch nodes where data replication occurs. Incoming MPLS labeled data is replicated to outgoing interfaces which may use different labels for the data. A P2MP TE Tunnel comprises one or more P2MP LSPs. A P2MP TE Tunnel is identified by a P2MP SESSION object. This object contains the identifier of the P2MP Session which includes the P2MP Identifier (P2MP ID), a tunnel Identifier (Tunnel ID) and an extended tunnel identifier (Extended Tunnel ID). The P2MP ID is a four octet number and is unique within the scope of the ingress LSR. The tuple provides an identifier for the set of destinations of the P2MP TE Tunnel. The fields of the P2MP SESSION object are identical to those of the SESSION object defined in [RFC3209] except that the Tunnel Endpoint Address field is replaced by the P2MP ID field. The P2MP SESSION object is defined in section 19.1 4.2. P2MP LSP A P2MP LSP is identified by the combination of the P2MP ID, Tunnel ID and Extended Tunnel ID that are part of the P2MP SESSION object, and the tunnel sender address and LSP ID fields of the P2MP SENDER_TEMPLATE object. The new P2MP SENDER_TEMPLATE object is defined in section 19.2. Raggarwa, Papadimitriou & Yasukawa [Page 6] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 4.3. Sub-Groups As with all other RSVP controlled LSPs, P2MP LSP state is managed using RSVP messages. While the use of RSVP messages is the same, P2MP LSP state differs from P2P LSP state in a number of ways. A P2MP LSP comprises multiple S2L Sub-LSPs and as a result of this it may not be possible to represent full state in a single IP packet. It must also be possible to efficiently add and remove endpoints to and from P2MP TE LSPs. An additional issue is that the P2MP LSP must also handle the state "remerge" problem, see [RFC4461] and section 18. These differences in P2MP state are addressed through the addition of a sub-group identifier (Sub-Group ID) and sub-group originator (Sub- Group Originator ID) to the SENDER_TEMPLATE and FILTER_SPEC objects. Taken together the Sub-Group ID and Sub-Group Originator ID are referred to as the Sub-Group fields. The Sub-Group fields, together with rest of the SENDER_TEMPLATE and SESSION objects, are used to represent a portion of a P2MP LSP's state. This portion of a P2MP LSP's state refers only to signaling state and not data plane replication or branching. For example, it is possible for a node to "branch" signaling state for a P2MP LSP, but to not branch the data associated with the P2MP LSP. Typical applications for generation and use of multiple sub-groups are adding an egress, and semantic fragmentation to ensure that a Path message remains within a single IP packet. 4.4. S2L Sub-LSPs A P2MP LSP is constituted of one or more S2L sub-LSPs. 4.4.1. Representation of an S2L Sub-LSP An S2L sub-LSP exists within the context of a P2MP LSP. Thus it is identified by the P2MP ID, Tunnel ID, and Extended Tunnel ID that are part of the P2MP SESSION, the tunnel sender address and LSP ID fields of the P2MP SENDER_TEMPLATE object, and the S2L sub-LSP destination address that is part of the S2L_SUB_LSP object. The S2L_SUB_LSP object is defined in section 19.3. An EXPLICIT_ROUTE Object (ERO) or P2MP_SECONDARY_EXPLICIT_ROUTE Object (SERO) is used to optionally specify the explicit route of a S2L sub-LSP. Each ERO or SERO that is signaled corresponds to a particular S2L_SUB_LSP object. Details of explicit route encoding are specified in section 4.5. The SECONDARY_EXPLICIT_ROUTE Object is defined in [RECOVERY], a new P2MP SECONDARY_EXPLICIT_ROUTE Object C- Raggarwa, Papadimitriou & Yasukawa [Page 7] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 type is defined in Section 19.5 and a matching P2MP_SECONDARY_RECORD_ROUTE Object C-type is defined in Section 19.6. 4.4.2. S2L Sub-LSPs and Path Messages The mechanism in this document allows a P2MP LSP to be signaled using one or more Path messages. Each Path message may signal one or more S2L sub-LSPs. Support for multiple Path messages is desirable as one Path message may not be large enough to contain all the S2L sub-LSPs; and they also allow separate manipulation of sub-trees of the P2MP LSP. The reason for allowing a single Path message, to signal multiple S2L sub-LSPs, is to optimize the number of control messages needed to set up a P2MP LSP. 4.5. Explicit Routing When a Path message signals a single S2L sub-LSP (that is, the Path message is only targeting a single leaf in the P2MP tree), the EXPLICIT_ROUTE object encodes the path to the egress-LSR. The Path message also includes the S2L_SUB_LSP object for the S2L sub-LSP being signaled. The < [], > tuple represents the S2L sub-LSP and is referred to as the sub-LSP descriptor. The absence of the ERO should be interpreted as requiring hop-by-hop routing for the sub-LSP based on the S2L sub-LSP destination address field of the S2L_SUB_LSP object. When a Path message signals multiple S2L sub-LSPs the path of the first S2L sub-LSP, to the egress-LSR, is encoded in the ERO. The first S2L sub-LSP is the one that corresponds to the first S2L_SUB_LSP object in the Path message. The S2L sub-LSPs corresponding to the S2L_SUB_LSP objects that follow are termed as subsequent S2L sub-LSPs. The path of each subsequent S2L sub-LSP is encoded in a P2MP_SECONDARY_EXPLICIT_ROUTE object (SERO). The format of the SERO is the same as an ERO (as defined in [RFC3209] and [RFC3473]). Each subsequent S2L sub-LSP is represented by tuples of the form < [] >. An SERO for a particular S2L sub-LSP includes only the path from a branch LSR to the egress- LSR of that S2L sub-LSP. The branch MUST appear as an explicit hop in the ERO or some other SERO. The absence of an SERO should be interpreted as requiring hop-by-hop routing for that S2L sub-LSP. Note that the destination address is carried in the S2L sub-LSP object. The encoding of the SERO and S2L_SUB_LSP object are described in detail in section 19. Raggarwa, Papadimitriou & Yasukawa [Page 8] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 In order to avoid the potential repetition of path information for the parts of S2L sub-LSPs that share hops, this information is deduced from the explicit routes of other S2L sub-LSPs using explicit route compression in SEROs. Explicit route compression is illustrated using Figure 1. A | | B | | C----D----E | | | | | | F G H-------I | |\ | | | \ | J K L M | | | | | | | | N O P Q--R Figure 1. Explicit Route Compression Figure 1. shows a P2MP LSP with LSR A as the ingress-LSR and six egress LSRs: (F, N, O, P, Q and R). When all the six S2L sub-LSPs are signaled in one Path message let us assume that the S2L sub-LSP to LSR F is the first S2L sub-LSP and the rest are subsequent S2L sub- LSPs. The following encoding is one way for the ingress-LSR A to encode the S2L sub-LSP explicit routes using compression: S2L sub-LSP-F: ERO = {B, E, D, C, F}, object-F S2L sub-LSP-N: SERO = {D, G, J, N}, object-N S2L sub-LSP-O: SERO = {E, H, K, O}, object-O S2L sub-LSP-P: SERO = {H, L, P}, object-P, S2L sub-LSP-Q: SERO = {H, I, M, Q}, object-Q, S2L sub-LSP-R: SERO = {Q, R}, object-R, After LSR E processes the incoming Path message from LSR B it sends a Path message to LSR D with the S2L sub-LSP explicit routes encoded as follows: S2L sub-LSP-F: ERO = {D, C, F}, object-F S2L sub-LSP-N: SERO = {D, G, J, N}, object-N Raggarwa, Papadimitriou & Yasukawa [Page 9] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 LSR E also sends a Path message to LSR H and following is one way to encode the S2L sub-LSP explicit routes using compression: S2L sub-LSP-O: ERO = {H, K, O}, object-O S2L sub-LSP-P: SERO = {H, L, P}, S2L_SUB_LSP object-P, S2L sub-LSP-Q: SERO = {H, I, M, Q}, object-Q, S2L sub-LSP-R: SERO = {Q, R}, object-R, After LSR H processes the incoming Path message from E it sends a Path message to LSR K, LSR L and LSR I. The encoding for the Path message to LSR K is as follows: S2L sub-LSP-O: ERO = {K, O}, object-O The encoding of the Path message sent by LSR H to LSR L is as follows: S2L sub-LSP-P: ERO = {L, P}, object-P, The following encoding is one way for LSR H to encode the S2L sub-LSP explicit routes in the Path message sent to LSR I: S2L sub-LSP-Q: ERO = {I, M, Q}, object-Q, S2L sub-LSP-R: SERO = {Q, R}, object-R, The explicit route encodings in the Path messages sent by LSRs D and Q are left as an exercise for the reader. This compression mechanism reduces the Path message size. It also reduces extra processing that can result if explicit routes are encoded from ingress to egress for each S2L sub-LSP. No assumptions are placed on the ordering of the subsequent S2L sub-LSPs and hence on the ordering of the SEROs in the Path message. All LSRs need to process the ERO corresponding to the first S2L sub-LSP. An LSR needs to process an S2L sub-LSP descriptor for a subsequent S2L sub-LSP only if the first hop in the corresponding SERO is a local address of that LSR. The branch LSR that is the first hop of an SERO propagates the corresponding S2L sub-LSP downstream. Raggarwa, Papadimitriou & Yasukawa [Page 10] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 5. Path Message 5.1. Path Message Format This section describes modifications made to the Path message format as specified in [RFC3209] and [RFC3473]. The Path message is enhanced to signal one or more S2L sub-LSPs. This is done by including the S2L sub-LSP descriptor list in the Path message as shown below. ::= [ ] [ [ | ] ...] [ ] [ ] [ ] [ ... ] [ ] [ ] [ ] [ ... ] [] Following is the format of the S2L sub-LSP descriptor list. ::= [ ] ::= [ ] Each LSR MUST use the common objects in the Path message and the S2L sub-LSP descriptors to process each S2L sub-LSP represented by the S2L_SUB_LSP object and the SECONDARY-/EXPLICIT_ROUTE object combination. Per the definition of , each S2L_SUB_LSP object MAY be followed by a corresponding SERO. The first S2L_SUB_LSP object is a special case, and its explicit route is specified by the ERO. Therefore, the first S2L_SUB_LSP object SHOULD NOT be followed by an SERO, and if one is present it MUST be ignored. The RRO in the sender descriptor contains the upstream hops traversed by the Path message and applies to all the S2L sub-LSPs signaled in the Path message. Raggarwa, Papadimitriou & Yasukawa [Page 11] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 An IF_ID RSVP_HOP object MUST be used on links where there is not a one-to-one association of a control channel to a data channel [RFC3471]. An RSVP_HOP object defined in [RFC2205] SHOULD be used otherwise. Path message processing is described in the next section. 5.2. Path Message Processing The ingress-LSR initiates the setup of an S2L sub-LSP to each egress- LSR that is a destination of the P2MP LSP. Each S2L sub-LSP is associated with the same P2MP LSP using common P2MP SESSION object and fields in the P2MP SENDER_TEMPLATE object. Hence it can be combined with other S2L sub-LSPs to form a P2MP LSP. Another S2L sub-LSP belonging to the same instance of this S2L sub-LSP (i.e. the same P2MP LSP) SHOULD share resources with this S2L sub-LSP. The session corresponding to the P2MP TE tunnel is determined based on the P2MP SESSION object. Each S2L sub-LSP is identified using the S2L_SUB_LSP object. Explicit routing for the S2L sub-LSPs is achieved using the ERO and SEROs. As mentioned earlier, it is possible to signal S2L sub-LSPs for a given P2MP LSP in one or more Path messages and a given Path message can contain one or more S2L sub-LSPs. An LSR that supports RSVP-TE signaled P2MP LSPs MUST be able to receive and process multiple Path messages for the same P2MP LSP and multiple S2L sub-LSPs in one Path message. This implies that such an LSR MUST be able to receive and process all objects listed in section 19. 5.2.1. Multiple Path Messages As described in section 4, either the < [] > or the < [] > tuple is used to specify an S2L sub-LSP. Multiple Path messages can be used to signal a P2MP LSP. Each Path message can signal one or more S2L sub-LSPs. If a Path message contains only one S2L sub-LSP, each LSR along the S2L sub-LSP follows [RFC3209] procedures for processing the Path message besides the S2L_SUB_LSP object processing described in this document. Processing of Path messages containing more than one S2L sub-LSP is described in Section 5.2.2. An ingress-LSR MAY use multiple Path messages for signaling a P2MP LSP. This may be because a single Path message may not be large enough to signal the P2MP LSP. Or it may be while adding leaves to Raggarwa, Papadimitriou & Yasukawa [Page 12] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 the P2MP LSP the new leaves are signaled in a new Path message. Or an ingress LSR MAY choose to break the P2MP tree into separate manageable P2MP trees. These trees share the same root and may share the trunk and certain branches. The scope of this management decomposition of P2MP trees is bounded by a single tree (the P2MP Tree) and multiple trees with a single leaf each (S2L sub-LSPs). Per [RFC4461], a P2MP LSP MUST have consistent attributes across all portions of a tree. This implies that each Path message that is used to signal a P2MP LSP is signaled using the same signaling attributes with the exception of the S2L sub-LSP descriptors and Sub-Group identifier. The resulting sub-LSPs from the different Path messages belonging to the same P2MP LSP SHOULD share labels and resources where they share hops to prevent multiple copies of the data being sent. In certain cases a transit LSR may need to generate multiple Path messages to signal state corresponding to a single received Path message. For instance ERO expansion may result in an overflow of the resultant Path message. In this case the message can be decomposed into multiple Path messages such that each message carries a subset of the X2L sub-tree carried by the incoming message. Multiple Path messages generated by an LSR that signal state for the same P2MP LSP are signaled with the same SESSION object and have the same in the SENDER_TEMPLATE object. In order to disambiguate these Path messages a tuple is introduced (also referred to as the Sub-Group fields) and encoded in the SENDER_TEMPLATE object. Multiple Path messages generated by an LSR to signal state for the same P2MP LSP have the same Sub-Group Originator ID and have a different sub-Group ID. The Sub-Group Originator ID MUST be set to the TE Router ID of the LSR that originates the Path message. Cases when a transit LSR may change the Sub-Group Originator ID of an incoming Path message are described below. The Sub-Group Originator ID is globally unique. The sub-Group ID space is specific to the Sub-Group Originator ID. 5.2.2. Multiple S2L Sub-LSPs in one Path message The S2L sub-LSP descriptor list allows the signaling of one or more S2L sub-LSPs in one Path message. Each S2L sub-LSP descriptor describes a single S2L sub-LSP. All LSRs MUST process the ERO corresponding to the first S2L sub-LSP if the ERO is present. If one or more SEROs are present an ERO MUST be present. The first S2L sub-LSP MUST be propagated in a Path message by each LSR along the explicit route specified by the ERO, if Raggarwa, Papadimitriou & Yasukawa [Page 13] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 the ERO is present. Else it MUST be propagated using hop-by-hop routing towards the destination identified by the S2L_SUB_LSP object. An LSR MUST process a S2L sub-LSP descriptor for a subsequent S2L sub-LSP as follows: If the S2L_SUB_LSP object is followed by an SERO, the LSR MUST check the first hop in the SERO: - If the first hop of the SERO identifies a local address of the LSR, and the LSR is also the egress identified by the S2L_SUB_LSP object, the descriptor MUST NOT be propagated downstream, but the SERO may be used for egress control per [RFC4003]. - If the first hop of the SERO identifies a local address of the LSR, and the LSR is not the egress as identified by the S2L_SUB_LSP object, the S2L sub-LSP descriptor MUST be included in a Path message sent to the next-hop determined from the SERO. - If the first hop of the SERO is not a local address of the LSR, the S2L sub-LSP descriptor MUST be included in the Path message sent to the LSR that is the next hop to reach the first hop in the SERO. This next hop is determined by using the ERO or other SEROs that encode the path to the SERO's first hop. If the S2L_SUB_LSP object is not followed by an SERO, the LSR MUST examine the S2L_SUB_LSP object: - If this LSR is the egress as identified by the S2L_SUB_LSP object, the S2L sub-LSP descriptor MUST NOT be propagated downstream. - If this LSR is not the egress as identified by the S2L_SUB_LSP object, the LSR MUST make a routing decision to determine the next hop towards the egress, and MUST include the S2L sub-LSP descriptor in a Path message sent to the next-hop towards the egress. In this case, the LSR MAY insert an SERO into the S2L sub-LSP descriptor. Hence a branch LSR MUST only propagate the relevant S2L sub-LSP descriptors to each downstream hop. An S2L sub-LSP descriptor list that is propagated on a downstream link MUST only contain those S2L sub-LSPs that are routed using that hop. This processing MAY result in a subsequent S2L sub-LSP in an incoming Path message becoming the first S2L sub-LSP in an outgoing Path message. Note that if one or more SEROs contain loose hops, expansion of such loose hops MAY result in overflowing the Path message size. Section 5.2.3 describes how signaling of the set of S2L sub-LSPs can be split across more than one Path message. Raggarwa, Papadimitriou & Yasukawa [Page 14] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 The RECORD_ROUTE Object (RRO) contains the hops traversed by the Path message and applies to all the S2L sub-LSPs signaled in the Path message. A transit LSR MUST append its address in an incoming RRO and propagate it downstream. A branch LSR MUST form a new RRO for each of the outgoing Path messages by copying the RRO from the incoming Path message and appending its address. Each such updated RRO MUST be formed using the rules in [RFC3209] updated by [RFC3473] as appropriate. If an LSR is unable to support an S2L sub-LSP in a Path message (for example, it is unable to route towards the destination using the SERO), a PathErr message MUST be sent for the impacted S2L sub-LSP, and normal processing of the rest of the P2MP LSP SHOULD continue. The default behavior is that the remainder of the LSP is not impacted (that is, all other branches are allowed to set up) and the failed branches are reported in PathErr messages in which the Path_State_Removed flag MUST NOT be set. However, the ingress-LSR may set an LSP Integrity flag to request that if there is a setup failure on any branch the entire LSP should fail to set up. This is described further in sections 5.2.4 and 11. 5.2.3. Transit Fragmentation of Path State Information In certain cases a transit LSR may need to generate multiple Path messages to signal state corresponding to a single received Path message. For instance ERO expansion may result in an overflow of the resultant Path message. RSVP [RFC2205] disallows the use of IP fragmentation and thus IP fragmentation MUST be avoided in this case. In order to achieve this, the multiple Path messages generated by the transit LSR, are signaled with the Sub-Group Originator ID set to the TE Router ID of the transit LSR and a distinct Sub-Group ID for each Path message. Thus each distinct Path message that is generated by the transit LSR for the P2MP LSP carries a distinct tuple. When multiple Path messages are used by an ingress or transit node, each Path message SHOULD be identical with the exception of the S2L sub-LSP related descriptor (e.g., SERO), message and hop information (e.g., INTEGRITY, MESSAGE_ID and RSVP_HOP), and the sub-group fields of the SENDER_TEMPLATE objects. Except when performing a make- before-break operation as specified in section 14.1, the tunnel sender address and LSP ID fields MUST be the same in each message, and for transit nodes, the same as the values in the received Path message. As described above one case in which the Sub-Group Originator ID of a received Path message is changed is that of fragmentation of a Path Raggarwa, Papadimitriou & Yasukawa [Page 15] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 message at a transit node. Another case is when the Sub-Group Originator ID of a received Path message may be changed in the outgoing Path message and set to that of the LSR originating the Path message based on a local policy. For instance an LSR may decide to always change the Sub-Group Originator ID while performing ERO expansion. The Sub-Group ID MUST not be changed if the Sub-Group Originator ID is not changed. 5.2.4. Control of Branch Fate Sharing An ingress-LSR can control the behavior of an LSP if there is a failure during LSP setup or after an LSP has been established. The default behavior is that only the branches downstream of the failure are not established, but the ingress may request 'LSP integrity' such that any failure anywhere within the LSP tree causes the entire P2MP LSP to fail. The ingress LSP may request 'LSP integrity' by setting bit TBD of the Attributes Flags TLV. (RFC Editor, please replace "TBD" with the bit number allocated by IANA per section 20.4. Please remove this note.) The bit is set if LSP integrity is required. It is RECOMMENDED to use the LSP_REQUIRED_ATTRIBUTES Object [RFC4420]. A branch LSR that supports the Attributes Flags TLV and recognizes this bit MUST support LSP integrity or reject the LSP setup with a PathErr message carrying the error "Routing Error"/"Unsupported LSP Integrity" 5.3. Grafting The operation of adding egress-LSR(s) to an existing P2MP LSP is termed as grafting. This operation allows egress nodes to join a P2MP LSP at different points in time. There are two methods to add S2L sub-LSPs to a P2MP LSP. The first is to add new S2L sub-LSPs to the P2MP LSP by adding them to an existing Path message and refreshing the entire Path message. Path message processing described in section 4 results in adding these S2L sub-LSPs to the P2MP LSP. Note that as a result of adding one or more S2L sub-LSPs to a Path message the ERO compression encoding may have to be recomputed. The second is to use incremental updates described in section 10.1. The egress LSRs can be added by signaling only the impacted S2L sub- Raggarwa, Papadimitriou & Yasukawa [Page 16] Internet Draft draft-ietf-mpls-rsvp-te-p2mp-07.txt January 2007 LSPs in a new Path message. Hence other S2L sub-LSPs do not have to be re-signaled. 6. Resv Message 6.1. Resv Message Format The Resv message follows the [RFC3209] and [RFC3473] format: ::= [ ] [ [ | ] ... ] [ ] [ ] [ ] [ ] [ ] [ ... ]